image-from-rawpixel-id-2354220-original_edited_edited.png

smart PRO

Want to optimize at low cost?

SMART PRO is the evolution of Elentek’s best-seller control

panel, suitable for both clean water and wastewater systems.

Thanks to the new expansion modules system and the connections, the panel can be used for a wide range of applications and increases the potential of the system.

Compact, very easy to install and program also by App, it facilitates the replacement of old and obsolete panels installed.

EASY INSTALLATION

average rating is 4 out of 5

USER INTERFACE

average rating is 4 out of 5

EXPANDABILITY

average rating is 5 out of 5

VERSATILITY

average rating is 4 out of 5

MAXIMUM CONTROL

01

Integrating the most complete system protections

ANTI-SEIZE

02

Pump unblocking function to prevent faults

INTUITIVE

03

Easy to set up and use

COMPETITIVE

04

The competitive control panel for several applications

FUNCTIONS

LEDs on front of panel for signaling operating status and alarms
AUTOMATIC - 0 (standby) - MANUAL pushbuttons (fixed or pulse)
Anti-seize autotest (can be disabled)
Dry running protection with: level probes/ floats/ pressure switches
Up to 4 control inputs: floats/pressure switches
Clicson inputs with automatic reset (can be disabled)
Inversion of inputs (from normally open to normally closed)
Start/stop float switch function (can be disabled)
Current protection delay
Automatic reset from minimum current alarm (can be disabled)
Delay time of motor enabling after power mains return
Pushbutton for manual operation (fixed or pulse)
Predisposition for run capacitors for single-phase version (not included)

ADDITIONAL FUNCTIONS SMART PRO 2

Duty/standby (can be disabled)
Immediate motor changeover in case of a fault

VERSIONS

Power supply 1phase 100-240Vac 50/60Hz
Power supply 3phase 310-450Vac 50/60Hz

CONTROLS

Electronic control of maximum current with assisted calibration
Electronic control of minimum current (dry running) with assisted calibration
Failure or incorrect phase sequence control on power supply input (can be disabled)

ALARMS

Alarms reported: voltage status, levels, motor overload, minimum motor current, clicson motor
General alarm output contacts

PROTECTIONS

Auxiliary and motor protection fuses
Isolator (except for NB code)
Box in ABS, IP55

CARATTERISTICHE PRINCIPALI

WATER IN OIL CHAMBER MODULE

BLUETOOTH WI-FI MODULE FOR APP

BUFFER BATTERY MODULE

BMS FREE VOLTAGE CONTACTS MODULE

LEVEL PROBES MODULE

RS485 MODBUS MODULE

✔

PRESSURISATION

✔

FILLING

✔

EMPTYING

✔

DRAINAGE

CONNETTIVITÀ

APPLICAZIONI

Scopri di più

RS485
(Optional)

RS485
(Optional)

EXPANDABILITY
MODULAR

CARATTERISTICHE CHIAVE

The electronic board of SMART PRO mounts an 8-switch dip-switch module to set the following modes of operation: level alarm signaling from probe input, amperometric protection trip delay, alarm output setting, alarm reset mode from motor clickson, fill/empty or pressurization operation mode, self-hold, and board activation delay from mains return.

Ammeter overcurrent protection and minimum current protection (dry run protection) is adjusted with trimmers on the board.

Key Features

COSA NON PUÓ MANCARE

Float DROP

COD:

DROP 20

Variable buoyancy float with 20 meters of cable

UNIT ALARM 2

COD:

UNIT ALARM 2

UNIT ALARM 2 is a device applicable to any system where it is necessary to have audible and visual flashing alarm signals, even in the absence of mains power.

APP

COD:

APP

The app allows you to control and manage the operation of the switchboard directly from your smartphone, adding features such as an operating counter, start-up counter, ammeter, history of the last 20 alarms, input and output status, and the ability to manage dip-switches and trimmers from your smartphone, increasing calibration accuracy.